01 · MoldWe machine the mold and measure it.
In tooling board, aluminum, cast iron, fiberglass or carbon fiber, with inserts when the geometry calls for them. We verify it with FARO before layup.
We develop and manufacture composite components in Ibi (Alicante), Spain: we machine the mold, measure it, laminate the part and measure it again. High-strength parts with optimal weight, even in highly complex geometries.
We manufacture custom orthoses and external supports — knee braces, lumbar and back supports, splints — that are lighter, thinner and stronger than conventional ones.
We start from a 3D scan or from the orthotist’s mold, and we work with professionals and manufacturers across the sector.
Tell us about your projectMaximum stiffness at minimum weight, in twill, plain or unidirectional fabric.
Impact and abrasion resistance, plus excellent resistance to acid attack.
The cost-effective choice for fairings, enclosures and molds.
Resins tailored to the thermal and mechanical demands of each project.
We develop our own systems to produce hollow parts and complex geometries.
01 · MoldIn tooling board, aluminum, cast iron, fiberglass or carbon fiber, with inserts when the geometry calls for them. We verify it with FARO before layup.
02 · LayupHand layup, infusion, RTM or out-of-autoclave (OOA) prepreg, depending on the finish, the use and the number of units.
03 · CuringWe cure in the oven at up to 200 °C. The autoclave is being commissioned and we activate it when a project requires it.
04 · TrimmingTwo 6-axis robots, one on a 7 m linear track, plus 5-axis machining centers.
05 · Finishing and inspectionA 60 m² pressurized paint booth and final dimensional inspection with FARO: every part leaves with its dimensions guaranteed.

Being commissioned: we activate it per project for aerospace-grade parts.
Climate-controlled clean room (207 m³) for prepreg layup and metrology.
Filament winding up to 4 m in diameter and 12 m in length.
Resin transfer molding and heated platen presses.
Prepregs stored at low temperature until use.
3 × 8 m autoclave being commissioned, available per project; today we cure prepreg in an oven.
TechnologiesPrepreg quality with more economical molds and cycles, oven-cured.
TechnologiesLarge parts with a good fiber-to-resin ratio, without prepreg.
TechnologiesClosed mold, two finished faces and repeatability in production.
TechnologiesPrototypes, one-off parts and complex geometries.
TechnologiesChopped fiber with a pattern that is unique on every part.
TechnologiesTubes, shafts and cylinders up to Ø 4 m and 12 m long.
TechnologiesKUKA robots and 5-axis up to 8 m for trimming and drilling composites.
TechnologiesMolds and patterns up to 8 × 3 × 2 m, measured before delivery.
Custom carbon orthoses and supports for orthotists.
IndustriesVisible and structural parts, large molds and patterns.
IndustriesPrepreg, tooling and metrology for aerospace.
IndustriesLight fuselages, arms and fairings, from prototype to production.
IndustriesBeams, rollers and lightweight components for machinery.
IndustriesLightweight components for sports equipment, from prototype to production.
IndustriesRTM molds, composites and machining with complete confidentiality.
We study your project with the same care you put into designing it, then send you a clear proposal covering process, lead time and price. Only have the physical part? We’ll scan it and take it from there.
It depends on the finish, how the part will be used and the number of units. We work with hand layup, infusion, RTM and out-of-autoclave prepreg, and we define the right process with you based on the application.
Yes. We design and machine the mold in our own plant, in tooling board, aluminum, cast iron, fiberglass or carbon fiber.
We cure in a 4 × 2 × 1.8 m oven at up to 200 °C. For larger parts, our 3 × 8 m autoclave is being commissioned and we activate it when a project requires it.